Results 1 to 9 of 9
  1. #1
    TV Addicted
    Join Date
    Oct 2015
    Location
    yes i do
    Posts
    22
    Rep Power
    0

    BuzzTV XPL 3000 2018 Model - No Signal

    So all was OK and suddenly I have No Signal on TV
    So I tried the usual

    Changed HDMI Port on TV
    Changed HDMI Cable
    Changed TV

    All samw - so I find RESET in the bottom but whats the proper way of doing it?
    I tried RESET - HOLD - POWER REMOVE,POWER ON - RESET STILL ON HOLD
    Now its just RED status, and NO SIGNAL

    Any advice?

  2. #2
    Transparent Wall Technician crazed 9.6's Avatar
    Join Date
    Nov 2014
    Posts
    15,650
    Rep Power
    447
    Quote Originally Posted by bhuvi100x View Post
    So all was OK and suddenly I have No Signal on TV
    So I tried the usual

    Changed HDMI Port on TV
    Changed HDMI Cable
    Changed TV

    All samw - so I find RESET in the bottom but whats the proper way of doing it?
    I tried RESET - HOLD - POWER REMOVE,POWER ON - RESET STILL ON HOLD
    Now its just RED status, and NO SIGNAL

    Any advice?
    disconnect hdmi
    disconnect power
    wait a second then reconnect power
    reconnect hdmi to powered up dreamlink

    any results ?
    "The illusion of freedom will continue for as long as it's profitable to continue the illusion. At the point where the illusion becomes too expensive to maintain, they will take down the scenery, move the tables and chairs out of the way, then they will pull back the curtains and you will see the brick wall at the back of the theater."
    - Frank Zappa

  3. #3
    Mercenary floder2's Avatar
    Join Date
    Dec 2014
    Location
    yea
    Posts
    2,704
    Rep Power
    143
    Are you sure your TV is on the correct input (HDMI 1 or HDMI 2)

  4. #4
    TV Addicted
    Join Date
    Oct 2015
    Location
    yes i do
    Posts
    22
    Rep Power
    0
    Quote Originally Posted by crazed 2.0 View Post
    disconnect hdmi
    disconnect power
    wait a second then reconnect power
    reconnect hdmi to powered up dreamlink

    any results ?
    Dreamlink?

    Ya did all that

  5. #5
    TV Addicted
    Join Date
    Oct 2015
    Location
    yes i do
    Posts
    22
    Rep Power
    0
    Quote Originally Posted by floder2 View Post
    Are you sure your TV is on the correct input (HDMI 1 or HDMI 2)
    Ya those were basic step, even tried different TV

  6. #6
    Mercenary floder2's Avatar
    Join Date
    Dec 2014
    Location
    yea
    Posts
    2,704
    Rep Power
    143
    The reset on the bottom of the box (Buzztv-Basic) hold in with paper clip ..with the power unplugged....while holding reset button in ..plug power back into the box ..wait 10 seconds ...then let go of the reset pin...

  7. #7
    Transparent Wall Technician crazed 9.6's Avatar
    Join Date
    Nov 2014
    Posts
    15,650
    Rep Power
    447
    this kinda thing is usually associated with HDMI issues ,as you guys probably know.

    If you have an HDMI Switch or access to one, I would try using that to fix the problem. I found when I had issues like HDMI not be recognized that after I used the Switch and then back to not using the Switch that the problem seemed to have gone away.
    Maybe its the power boost that the Switch sends to the HDMI port that fixes it, I do not know, but did seem to work for me.

    Them HDMI Switches are not cheap thou, so make that your last resort and follow floder's methods first
    "The illusion of freedom will continue for as long as it's profitable to continue the illusion. At the point where the illusion becomes too expensive to maintain, they will take down the scenery, move the tables and chairs out of the way, then they will pull back the curtains and you will see the brick wall at the back of the theater."
    - Frank Zappa

  8. #8
    TV Addicted
    Join Date
    Oct 2015
    Location
    yes i do
    Posts
    22
    Rep Power
    0
    I contacted Buzz and they asked me to send to them and they fix and send back - but I assume there would be a simpler fix
    I am interested in crazed 2.0's reponse, I did use a HDMI splitter with a HDMI switch. The splitter split the signal, and then went to a HDMI to RGB ( for DVD Recorder ), but I then use direct to TV as I didnt want that setup
    All worked but then now no signal

  9. #9
    TV Addicted
    Join Date
    Oct 2015
    Location
    yes i do
    Posts
    22
    Rep Power
    0
    It was bad HDMI, but its all my faulkt - my TV has like 10 wires in the back and the HDMI I was connecting was from a different source all together

 

 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •