Stalker unable to load channels

[dinkish]

This procedure works for me with 'Unable to load channels':

1. Delete your current MAC and set up a new one. Save.

2. Go to KODI Settings ==> TV==> and Disable

3. go to My Addons ==> PVR Clients ==> Stalker client ===> Disable

4. Configure and change the MAC to the new one you saved. Type OK. Make sure you have entered your Logon/Password value (from your Userid/password)

5. Configure Serial ( twelve numbers and the last digit a letter)

6. Configure Device 1 (any four numbers), Configure Device 2 (any four numbers, but different from Device 1), Configure Signature (your last name)...CLICK ok

7. Enable the Stalker client addon. Do to KODI Settings ==> TV ==> Enable

8. If it still won't loqad, Reboot KODI and see if that works.

Good Luck..

Did all that earlier, still received the same error, I'll test it again later.

[vampirito]

Ok, now working here. This is what i did:

1. Go to settings, TV, general, unckeck "enable" and click on "clear data"
2. Go to settings, addons, my addons, pvr stalker, disable.
3. Under pvr stalker settings, configure, added credentials, click OK
3. Go to papiao site and deleted my MAC, click save and It reset to 00's. Waited 3 minutes just to give it time to reset.
4. Go in again to papiao and re-added my MAC, save and waited 2 minutes.
5. Go to kodi addons and re-enable pvr stalker
6. Go to settings, general, re-check "enable". It should load now. If not, reboot Kodi and get in again.

[psycon]

set timeout to 120 and reconnect.. as long as its set up properly it should reconnect.

[dinkish]

Loaded it up, took a while, but channels loaded up this time. No guide data still however.

[aglloret]

Ok, now working here. This is what i did:

1. Go to settings, TV, general, unckeck "enable" and click on "clear data"
2. Go to settings, addons, my addons, pvr stalker, disable.
3. Under pvr stalker settings, configure, added credentials, click OK
3. Go to papiao site and deleted my MAC, click save and It reset to 00's. Waited 3 minutes just to give it time to reset.
4. Go in again to papiao and re-added my MAC, save and waited 2 minutes.
5. Go to kodi addons and re-enable pvr stalker
6. Go to settings, general, re-check "enable". It should load now. If not, reboot Kodi and get in again.

This worked for me beautifully. Thanks!!!

[dotsadie]

How do you get time out set to 120 mine only goes to 15?

[JD95]

Ok, now working here. This is what i did:

1. Go to settings, TV, general, unckeck "enable" and click on "clear data"
2. Go to settings, addons, my addons, pvr stalker, disable.
3. Under pvr stalker settings, configure, added credentials, click OK
3. Go to papiao site and deleted my MAC, click save and It reset to 00's. Waited 3 minutes just to give it time to reset.
4. Go in again to papiao and re-added my MAC, save and waited 2 minutes.
5. Go to kodi addons and re-enable pvr stalker
6. Go to settings, general, re-check "enable". It should load now. If not, reboot Kodi and get in again.

I'll give this a go tonight. Thanks.

[JD95]

When you say you added your credentials, what did you use? was it your donation/route number?


EDIT - yes, it is. Thanks, works perfectly.

[lopeztiti]

using stalker client 8.4 you need to put in login and password your donation number ..

[karateman1]

I have my login information in i changed my mac but i still get unable to load channels i was working earlier now i have nothing did all the steps suggested but still cant get it to work any help please ?