mag254 infomir logo

[nahida]

on power up, message, stb is damaged.
i did a factory reset, then loaded the latest firmware successfully and working fine, but no red infomir screen on power up. only a blue screen. image is 218, am using RCA cable as my tv has no HDMI port, but has a component port. before the factory reset i did see the infomir logo. how can i get the red logo back up? thanks

[Bkman2020]

This happens when you erase user data on your unit you cannot get the informir logo unless you know how to use lunix based commands.

[nahida]

This happens when you erase user data on your unit you cannot get the informir logo unless you know how to use lunix based commands.

At last I restored the red infomir logo back.
I loaded the logo file and update_logo.sh file to flash drive. connected flash drive to stb.
used putty to communicate with stb, and loaded the files and finally reboot.
i have no knowledge on linux based commands, but did a lot of reading.
if anybody restores mag to factoy settings, then red logo will disappear.

[bigdummy]

perhaps you could post the step you took to help other members

[Bkman2020]

i tried it but my isp blocks port 22 i believe so.

[nahida]

[QUOTE=Bkman2020;4044]i tried it but my isp blocks port 22 i believe so.[/QUOTE

First u need to load the public image which has ssh open. U have to load public image using Mcast. Public image is available from infomir website. Or,

Send an email to tech support infomir, and they will help u out. I followed their instructions to get logo back

[Marley]

a box factory reset will give all back look in mag section

[Bkman2020]

That doesn't bring back the logo but restores unit back to factory settings thanks.

[zensat]

[QUOTE=Bkman2020;4044]i tried it but my isp blocks port 22 i believe so.[/QUOTE

First u need to load the public image which has ssh open. U have to load public image using Mcast. Public image is available from infomir website. Or,

Send an email to tech support infomir, and they will help u out. I followed their instructions to get logo back

you mind share here in the forum?
thanx

[Bkman2020]

Got in contact with informir they send me simple easy steps if it works i will post it on here with mod`s permission. thanks

[theone]

Got in contact with informir they send me simple easy steps if it works i will post it on here with mod`s permission. thanks

You can post it in the download section if its a file. If its a text fix then you can post it here.

[Bkman2020]

Open "System settings" -> "Software update"
- Change current URL for updating to hxxp://mag.infomir.com.ua/r2/imageupdate_logo
- Press "OK" and update STB

[theone]

Open "System settings" -> "Software update"
- Change current URL for updating to hxxp://mag.infomir.com.ua/r2/imageupdate_logo
- Press "OK" and update STB

Note: I HAVE NOT TESTED THIS YET.
Thanks going to test it right now since I have an extra box that lost the infomir logo.

[Bkman2020]

Thanks let me know the results.

[theone]

Thanks let me know the results.

Ok it worked, infomir image has returned lol.

[Bkman2020]

Great thanks

[Bkman2020]

Make it a sticky if you like

[theone]

Make it a sticky if you like

Done thanks bro

http://iptvtalk.net/showthread.php?614-How-to-get-Infomir-logo-back&p=4626#post4626

[zensat]

it gives me error "invalid header"...probably because already updated box to 218.r10 firmaware that is not yet loaded at that address....i will wait Infomir post r10 at the address and retry....
ThaNK you so much BK

[kinch]

invalid header for me two

[Bkman2020]

Bad error header problem? Here`s a quick fix: Restore to def settings in bios then re-do steps again. Worked for me perfect.

[Bkman2020]

When the box goes back to default settings under bios settings it goes back to earlier firmware version and that's when you can add _logo at the end of the url in the software update settings and hit ok should update firmware without any errrors.

[K00lKatT]

thks for the clarification, Brooklyn, just curious if after will your box give the update reminder

[Bkman2020]

yes after your done installing lastest firmware and your box reboots you will need to go back and erase just _logo and you will get future reminder updates.

[K00lKatT]

thks...BK..

[Bkman2020]

This process all it does when you add _logo to the url it reinstalls the latest firmware and pushes the logo update