PDA

View Full Version : What is wrong when----


kcmood
06-28-2018, 11:19 PM
My mag 254 is giving me a hard time. I can turn it on, it will have the imfomir logo it gets to loading and it is stuck there. Is there something I can do to fix this?
tonyd33
06-29-2018, 03:01 AM
My mag 254 is giving me a hard time. I can turn it on, it will have the imfomir logo it gets to loading and it is stuck there. Is there something I can do to fix this?

Do you get to the yellow bar.
kcmood
06-29-2018, 12:02 PM
No, I do not get beyond the first loading. It should goto a black screen that says loading and then the yellow bar. I also cannot turn it off unless I unplug the power cord.
In other words the first loading is with the infomir logo, then a black screen with a loading again then the yellow bar.
tonyd33
06-29-2018, 05:01 PM
Go into BIOS and scroll down to DEF.SETTINGS and reset,also make sure boot mode says nand.
kcmood
06-29-2018, 08:05 PM
I will try that again but I have tried repeatably and the bios will not come up
kcmood
06-29-2018, 08:55 PM
I went into bios again and am where I was before. When I plug in power cord I get "loading from nand, then checking image, then loading". That is where it sits for about 30 - 40 sec and then screen goes black and it cuts off. I will add, which I should have done before, we had a thunder and lightning storm the day it went off and ever since its not working. We did not lose power but we had a powerful storm and my tv in bedroom was fried, it came thru the antenna OTA. The iptv box is in the living room.
tonyd33
06-29-2018, 09:02 PM
Go back to bios and lower the resolution.
kcmood
06-29-2018, 11:10 PM
Will have to try that tomorrow. Off to work I go
chevy69
06-30-2018, 12:03 AM
reboot modem, router, then try it, unplug cat5 and try it if rebooting does not work, it should still load, but tell you internet out,
kcmood
06-30-2018, 01:32 PM
reboot modem, router, then try it, unplug cat5 and try it if rebooting does not work, it should still load, but tell you internet out,

I unplugged the cat 5 as you suggested but it still will not load. Any other suggestions?
tonyd33
06-30-2018, 11:19 PM
My friend had the same problem and found out later that his kid had changed to a higher resolution thinking he would get a better picture but it locked down his mag from loading.If you make changes in BIOS make sure you hit EXIT & SAVE.My bios settings are (720p-60)(1280x720)(nand).
kcmood
07-01-2018, 10:03 AM
My friend had the same problem and found out later that his kid had changed to a higher resolution thinking he would get a better picture but it locked down his mag from loading.If you make changes in BIOS make sure you hit EXIT & SAVE.My bios settings are (720p-60)(1280x720)(nand).

Thats what mine are set at.
4me2c
07-01-2018, 12:21 PM
https://youtu.be/nXuDmmoqtxA

Are You doing what this shows at 1:02 in...?!?

Not sure but, I have a MX Box that looks similar to Your STB, in the back there is the AV Port and I can stick a wooden Toothpick inside slowly till it bottoms out and then I can fell a Click which is another way to Re-Boot and Reset the STB...! Again, Not Sure if that will work with Your Stab... Other Boxes have that availability also : http://iptvtalk.net/showthread.php?36759-pin-hole-reset
tonyd33
07-01-2018, 04:34 PM
Try another HDMI cable.
kcmood
07-01-2018, 07:35 PM
Try another HDMI cable.

Did that already